Cleaning and Storing Toys the Right Way
If you’ve read a few reviews on here you’ll have noticed most of them finish the same way: hot water, antibacterial soap, a bit of sex toy cleaner and leave it to dry. That’s the short version and for a lot of toys it’s all you need. But different materials need different treatment, toys with motors have their own rules, and how you store everything matters almost as much as how you wash it. So here’s the long version.
Start With the Material
Before you clean anything, know what it’s made of, because that decides what you can do with it.
- Non-porous: silicone, glass, stainless steel and hard ABS plastic. These can be cleaned properly, and some of them can be sterilised.
- Porous: jelly, PVC, TPE, TPR and most of the soft, realistic “skin” materials used in masturbators. Bacteria can live in the surface where soap can’t reach, so these can never be fully sanitised. Use a condom on them where you can, keep them to one person, and replace them regularly.
If you’re still deciding what to buy, that’s a big part of why I’d always point you towards silicone, glass or steel. There’s more on the pros and cons in Silicone, Glass or Steel: Choosing a Plug Material.
The Everyday Clean
- Clean it straight away, not tomorrow morning. Dried lube and bodily fluids are much harder to shift.
- Use warm water and a mild, unscented soap or a dedicated toy cleaner. Harsh, perfumed soaps can irritate skin and some can damage softer materials.
- Get into every ridge, seam, button and the join between shaft and base. That’s where everything hides.
- Rinse thoroughly. Soap residue left on an insertable toy is a good way to end up sore next time.
- Pat it dry with a lint-free cloth or leave it somewhere clean to air dry completely before putting it away.
Anything that’s been used anally needs washing before it goes anywhere else, or swap the condom on it. No exceptions.
Masturbator sleeves need a bit more effort than most. Rinse the inside with warm water until it runs clear, turn it inside out if the design allows, and leave it somewhere airy until the inside is bone dry. A sleeve that gets put away damp will grow something, and you don’t want to find out what. Silicone lube also clings to glass and steel, so if you’ve used it, give those a proper soapy wash rather than a quick rinse.
Deep Cleaning and Sterilising
Every so often, after sharing a toy or after an infection, it’s worth going further than soap and water. What you can do depends on the material:
- 100% silicone with no motor: a few minutes in boiling water does the job.
- Glass: put it in a pan of cold water, bring it up to temperature slowly and let it cool down in the water. Sudden temperature changes are what crack glass.
- Stainless steel: boil it. It doesn’t care.
- Anything with a motor or battery, and anything porous: never boil it. Soap, water and a toy cleaner are your limit, and porous toys should simply be replaced more often.
Toys With Motors and Batteries
Check what the manufacturer actually means by waterproof. “Splash-proof” means a wipe with a damp cloth and nothing more. Fully waterproof toys can go under the tap, but make sure any charging port cover is shut and any battery compartment is sealed first. Toys with magnetic charging points need those contacts wiped and dried before they go back on the charger, because water and charging contacts don’t mix. If you’re not going to use a toy that takes disposable batteries for a while, take them out, because a leaking battery will ruin it.
E-Stim Kit and Bondage Gear
Electro gear needs a bit of extra care. Insertable electrodes get washed like any other toy, with special attention to where the metal meets the insulator, and they must be completely dry before storage. Some, like the E-Stim Systems Black Collection, can be taken apart, which makes a thorough clean far easier. Wipe cables down without soaking the connectors, and coil them loosely rather than wrapping them tight around the unit.
Self-adhesive pads are personal kit. Put them back on their backing sheet after use and replace them once they stop sticking properly. A pad that won’t lie flat isn’t just annoying, it’s a safety issue, as explained in Getting Started With E-Stim: Safety First.
Leather cuffs, collars and floggers should never be soaked. Wipe them down with a damp cloth or a proper leather cleaner, let them dry naturally away from radiators, and condition them now and then so they don’t crack. Steel cuffs and chastity devices get washed and dried thoroughly like any other steel toy.
Storing It All
- Dry first, always. Putting a damp toy in a bag or box is how mould starts.
- Keep porous toys separate. Jelly and similar soft materials can react with other toys they’re pressed against and leave both of them damaged. Give them their own space.
- One toy, one bag. A cloth pouch per toy keeps dust and lint off silicone and stops glass and steel knocking into each other. Some packaging is good enough to keep. The box the Nexus Ace comes in works for storage, for example, while plenty of others are only fit for the recycling.
- Cool, dark and dry. Not on a windowsill, not next to a radiator and not in a damp bathroom cupboard.
- Look after batteries. Rechargeable toys don’t like being left completely flat for months, so give them a top-up every so often.
When to Bin It
No toy lasts forever. Get rid of anything with cracks, chips or tears, any silicone that has gone sticky or tacky, anything with a smell that won’t wash out, and any porous toy that has started to discolour. A chipped glass toy or a torn silicone surface isn’t worth the risk, however much you loved it. Wash it, dry it, store it properly, and your good toys will last you years.
Sorry - Comments are closed
